How to change the oil on your Sea‑Doo personal watercraft?

Changing the oil on your Sea-Doo personal watercraft is a necessity of Sea-Doo PWC maintenance. It’s a quick and simple process that most at-home mechanics will be comfortable performing. What’s a good rule of thumb? Your PWC oil should be changed annually, and it’s typically recommended to keep it as an end-of-season maintenance item. This quick guide on how to change your personal watercraft oil will walk you through all the steps.

Required tools for a PWC oil change

  • Oil change kit for your Rotax 900 ACE or 1630 ACE engine, such as the XPS Oil Change Kit. This includes everything you need to complete an oil change.
  • Manual fluid extractor

  • Drain pan 

  • E8 external torx socket and socket wrench

  • Torque wrench

  • Funnel and a few rags

  • Protective equipment (rubber gloves, safety glasses, close-toed shoes)


Sea-Doo PWC oil change process


Park your PWC on a level surface. Firmly chock the trailer tires. Use the trailer jack to level the PWC if needed.


Remove the seat and engine access cover of your PWC. This allows you to check for any signs of coolant or oil leaks that may need attention.

 /!\ DANGER /!\ DO NOT run the engine indoors or without adequate ventilation or permit exhaust fumes to accumulate in confined areas. Engine exhaust contains carbon monoxide (CO) which, if inhaled, can cause serious brain damage or death.



Warm up the engine following the exhaust flushing instructions found in your operator’s guide. Remember, never run your engine without supplying water to the exhaust system and never run it for more than 2 minutes at a time. Repeat the engine warm-up process twice, letting the drive shaft cool down for 5 minutes between each cycle.

Run the engine for 10 seconds at 4,000 RPM and shut it off at this RPM by pulling the tether cord. This will move oil from the PTO housing to the oil tank to allow maximum oil draining.


Extract the old engine oil. Rather than draining the oil like you would from a car, use the fluid extractor to pump the oil out of your Sea-Doo PWC and into a drain pan.

Remove the dipstick and oil fill cap. Place one end of the fluid extractor hose into the dipstick opening. For a Rotax 900 ACE engine, insert the extraction tube 400 mm or 15.75 in. For a Rotax 1630 ACE engine, insert the tube 475 mm or a little more than 18.5 in. Place the other end of the fluid extractor hose into your drain pan and pump the old oil out.

Sea-Doo pro tip: Measure the end of the tube to be inserted and quickly mark the proper distance with a piece of tape. This will save you time, and maybe even a minor headache.

Remove the extractor hose from the dipstick tube, then reinstall the fill cap and the dipstick. Reattach the tether cord. Fully depress the throttle lever and HOLD it while pressing the start button to crank the engine for 10 seconds. Siphon the oil again. Repeat the crank-siphon cycle two or three times to remove all the old oil.


Remove the oil filter cover and old oil filter with the E-8 external torx driver. On most models, there’s just one bolt — but the Sea-Doo Spark PWC comes with three bolts to remove. Be careful not to drop them into the hull. Set the bolt(s) aside and remove the old O-ring(s).

NOTE: 900 ACE engines will have just one O-ring. The 1630 ACE engines will have two O-rings you’ll need to replace.

Carefully remove the old oil filter. You’ll want a rag to catch any drips. Wipe the filter cover clean and inspect the oil filter housing for any debris and clean if needed.


 Install the new oil filter and replace the O-ring(s). Lightly oil the new oil filter ring and O-ring(s) with fresh oil so they can seal tightly. Reinstall the oil filter cover and torque bolts to 9 N·m ± 1 N·m (80 lbf·in ± 9 lbf·in).

Sea-Doo pro tip: In saltwater areas, it is recommended to coat the mating surface of the cover with grease.


Fill with fresh oil and replace the oil fill cap (or dipstick if you have a Rotax 900 ACE engine). The XPS Oil Change Kit comes with the required amount of oil for your Sea-Doo PWC.  If you’re not using an oil change kit, refer to the operator’s guide for the proper quantities.


Verify the proper oil level. Using the same engine warm-up procedure, bring engine RPM to 4,000–4,500 RPM for 15 seconds. Stop the engine abruptly by pressing the start/stop button or removing the tether cord. Wait at least 30 seconds for the oil to settle in the engine and check the oil levels. Adjust as required.


Reinstall the engine access cover and seat (if required). Now you’re ready to ride.

STEP 10:

Dispose of your old oil and filter properly. If you’re not sure where to do this, contact your local municipality for proper oil disposal locations and procedures.

With your Sea-Doo PWC oil change complete, you’re ready to head back to the boat ramp, keep living your favorite adventures to the fullest and chase the joy up and down every wave. If you have any questions about the Sea-Doo oil change process, be sure to reach out to your authorized Sea-Doo dealer. We’ll see you on the water!

Frequently asked questions

  • Vehicle Information
    Where should I have my <br> Sea-Doo PWC serviced? <br> Can I do it myself?

    Where should I have my
    Sea-Doo PWC serviced?
    Can I do it myself?

    Learn More
  • Vehicle Information
    Can you run the motor of your Sea-Doo out of the water?

    Can you run the motor of your Sea-Doo out of the water?

    Learn More
  • Vehicle Information
    How to check your Sea-Doo Personal Watercraft steering alignment?

    How to check your Sea-Doo Personal Watercraft steering alignment?

    Learn More

Can't find what you're looking for?

If you still can't find what you're looking for, get in touch with your local dealer or reach out to us here!